vin-number

HALE

HALE KUBOTA PORTABLE PUMP 0

Hale Products Inc (Hale) is recalling certain Kubota Diesel Powered Portable Pumps, part number 200779, revisions A through C. These pumps may be improperly wired, causing the Oil Pressure and Temperature warning lamps to not illuminate when needed.
HALE VALVE RETAINING RING 0

Hale Products Inc. (Hale) is recalling certain retaining rings, part number 077-0750-21-0, that secure the pressure relief valve in the water pumps used for fire fighting. These rings may corrode over time after exposure to water, causing the ring to fail and the pressure relief valve to open, reducing the available water pressure.
HALE PUMP PRESSURE SWITCH 0

Hale Products Inc. (Hale) is recalling certain Fire Pump Engagement Pressure Switches, part number 200-2560-00-0. These pressure switches are used to initiate the fire pump gearbox engagement with an interlock module when retrofitted to existing air shift control for the fire pump. These switches may fail during extremely cold temperatures, preventing the truck's water pump from being put into gear.
HALE PUMP PRESSURE SWITCH 0

Hale Products Inc. (Hale) is recalling certain Fire Pump Engagement Pressure Switches, part number 200-2560-00-0. These pressure switches are used to initiate the fire pump gearbox engagement with an interlock module when retrofitted to existing air shift control for the fire pump. These switches may fail during extremely cold temperatures, preventing the truck's water pump from being put into gear.
HALE PORTABLE YANMAR PUMP 0

Hale Products Inc. (Hale) is recalling certain Portable Pumps powered with Yanmar 9 horsepower diesel engines, manufactured March 1, 2007, to December 11, 2015. These pumps may incorrectly identify the warning light on the dash panel to warn of low oil pressure when the warning light actually warns of low battery charge.
HALE PORTABLE YANMAR PUMP 0

Hale Products Inc. (Hale) is recalling certain Portable Pumps powered with Yanmar 9 horsepower diesel engines, manufactured March 1, 2007, to December 11, 2015. These pumps may incorrectly identify the warning light on the dash panel to warn of low oil pressure when the warning light actually warns of low battery charge.
HALE 6 INCH SUCTION STRAINER 0

Hale Products Inc. (Hale) is recalling certain 6 Inch Suction Strainers, part number 010-0030-00-0, manufactured July 15, 2015, to March 30, 2016. The affected strainers may have been improperly soldered leaving the strainer weak, which can cause the strainer to break and allow the strainer and debris to enter and possibly damage the fire pump.
HALE QUENCHING AGENT SENSOR 0

Hale Products Inc. (Hale) is recalling certain Quenching Agent Level Pressure Sensors, Class 1 ITL Level Displays, manufactured May 1, 2015, to July 31, 2015. When the vehicle is stationary, the affected sensors may give an incorrect reading of the remaining fire fighting agent (typically water or firefighting foam) left in the tank.
HALE K GEARBOX 0

Hale Products Inc. (Hale) is recalling certain K Gearboxes manufactured December 20, 2014, to August 3, 2015. These gearboxes are used in fire apparatus to transfer engine power from driving a fire hose pump to turning the vehicle driveshaft. The affected gearboxes, sizes XK and LK, may shift out of gear from road to neutral while in the fire truck is in transit.
HALE PARKER 2000

ON CERTAIN DUMP TRAILERS EQUIPPED WITH SEALCO SPRING BRAKE CONTROL VALVE ASSEMBLIES INCORPORATED IN ARVINMERITOR AXLES, PART NOS. 110700 AND 110800, THERE IS A RECESSED AREA ON TOP OF THE VALVE IN WHICH A BRASS GUIDE PIN FITS DOWN INSIDE THE BODY OF THE VALVE AND IS HELD IN PLACE BY A STEEL SNAP RING. THE RECESSED AREA ALLOWS ACCUMULATION OF WATER, DIRT, AND/OR CHEMICALS TO BUILD UP BEHIND THE SNAP RING TO THE POINT WHERE IT WILL NO LONGER CONTAIN THE GUIDE PIN RESULTING IN A FAILURE OF THE AIR VALVE.
HALE PARKER 1999

ON CERTAIN DUMP TRAILERS EQUIPPED WITH SEALCO SPRING BRAKE CONTROL VALVE ASSEMBLIES INCORPORATED IN ARVINMERITOR AXLES, PART NOS. 110700 AND 110800, THERE IS A RECESSED AREA ON TOP OF THE VALVE IN WHICH A BRASS GUIDE PIN FITS DOWN INSIDE THE BODY OF THE VALVE AND IS HELD IN PLACE BY A STEEL SNAP RING. THE RECESSED AREA ALLOWS ACCUMULATION OF WATER, DIRT, AND/OR CHEMICALS TO BUILD UP BEHIND THE SNAP RING TO THE POINT WHERE IT WILL NO LONGER CONTAIN THE GUIDE PIN RESULTING IN A FAILURE OF THE AIR VALVE.
HALE PARKER 1998

ON CERTAIN DUMP TRAILERS EQUIPPED WITH SEALCO SPRING BRAKE CONTROL VALVE ASSEMBLIES INCORPORATED IN ARVINMERITOR AXLES, PART NOS. 110700 AND 110800, THERE IS A RECESSED AREA ON TOP OF THE VALVE IN WHICH A BRASS GUIDE PIN FITS DOWN INSIDE THE BODY OF THE VALVE AND IS HELD IN PLACE BY A STEEL SNAP RING. THE RECESSED AREA ALLOWS ACCUMULATION OF WATER, DIRT, AND/OR CHEMICALS TO BUILD UP BEHIND THE SNAP RING TO THE POINT WHERE IT WILL NO LONGER CONTAIN THE GUIDE PIN RESULTING IN A FAILURE OF THE AIR VALVE.
HALE PARKER 1997

ON CERTAIN DUMP TRAILERS EQUIPPED WITH SEALCO SPRING BRAKE CONTROL VALVE ASSEMBLIES INCORPORATED IN ARVINMERITOR AXLES, PART NOS. 110700 AND 110800, THERE IS A RECESSED AREA ON TOP OF THE VALVE IN WHICH A BRASS GUIDE PIN FITS DOWN INSIDE THE BODY OF THE VALVE AND IS HELD IN PLACE BY A STEEL SNAP RING. THE RECESSED AREA ALLOWS ACCUMULATION OF WATER, DIRT, AND/OR CHEMICALS TO BUILD UP BEHIND THE SNAP RING TO THE POINT WHERE IT WILL NO LONGER CONTAIN THE GUIDE PIN RESULTING IN A FAILURE OF THE AIR VALVE.
HALE PARKER 1996

ON CERTAIN DUMP TRAILERS EQUIPPED WITH SEALCO SPRING BRAKE CONTROL VALVE ASSEMBLIES INCORPORATED IN ARVINMERITOR AXLES, PART NOS. 110700 AND 110800, THERE IS A RECESSED AREA ON TOP OF THE VALVE IN WHICH A BRASS GUIDE PIN FITS DOWN INSIDE THE BODY OF THE VALVE AND IS HELD IN PLACE BY A STEEL SNAP RING. THE RECESSED AREA ALLOWS ACCUMULATION OF WATER, DIRT, AND/OR CHEMICALS TO BUILD UP BEHIND THE SNAP RING TO THE POINT WHERE IT WILL NO LONGER CONTAIN THE GUIDE PIN RESULTING IN A FAILURE OF THE AIR VALVE.
HALE PARKER 1995

ON CERTAIN DUMP TRAILERS EQUIPPED WITH SEALCO SPRING BRAKE CONTROL VALVE ASSEMBLIES INCORPORATED IN ARVINMERITOR AXLES, PART NOS. 110700 AND 110800, THERE IS A RECESSED AREA ON TOP OF THE VALVE IN WHICH A BRASS GUIDE PIN FITS DOWN INSIDE THE BODY OF THE VALVE AND IS HELD IN PLACE BY A STEEL SNAP RING. THE RECESSED AREA ALLOWS ACCUMULATION OF WATER, DIRT, AND/OR CHEMICALS TO BUILD UP BEHIND THE SNAP RING TO THE POINT WHERE IT WILL NO LONGER CONTAIN THE GUIDE PIN RESULTING IN A FAILURE OF THE AIR VALVE.
HALE PARKER 1994

ON CERTAIN DUMP TRAILERS EQUIPPED WITH SEALCO SPRING BRAKE CONTROL VALVE ASSEMBLIES INCORPORATED IN ARVINMERITOR AXLES, PART NOS. 110700 AND 110800, THERE IS A RECESSED AREA ON TOP OF THE VALVE IN WHICH A BRASS GUIDE PIN FITS DOWN INSIDE THE BODY OF THE VALVE AND IS HELD IN PLACE BY A STEEL SNAP RING. THE RECESSED AREA ALLOWS ACCUMULATION OF WATER, DIRT, AND/OR CHEMICALS TO BUILD UP BEHIND THE SNAP RING TO THE POINT WHERE IT WILL NO LONGER CONTAIN THE GUIDE PIN RESULTING IN A FAILURE OF THE AIR VALVE.
HALE HALE 1969
HALE HALE 1970
HALE HALE 1968