FORD RANCHERO
-
FORD RANCHERO 1979
INTERCONTINENTAL AUTO PARTS IS RECALLING 1,937 FUEL FILTERS, P/NOS ALG 44/1 AND PUROLATOR F10024, SHIPPED BETWEEN JANUARY 14 AND FEBRUARY 13, 2008, SOLD FOR USE ON THE VEHICLES LISTED ABOVE. THE FILTER'S OUTLET CAP MAY NOT BE SECURELY CRIMPED TO THE HOUSING. THIS COULD RESULT IN A SEPARATION OF FILTER'S OUTLET CAP FROM THE HOUSING.
-
FORD RANCHERO 1976
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
-
FORD RANCHERO 1975
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
-
FORD RANCHERO 1977
BLADES MAY CRACK AND MAY, OVER A PERIOD OF TIME, LOOSEN FROM FAN ASSEMBLY.
-
FORD RANCHERO 1979
THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH INCORRECT WELD NUTS THAT ATTACH THE REAR PORTION OF THE FRONT OUTBOARD SEAT TRACK TO THE FLOOR PAN. THE INCORRECT NUTS HAVE AN OVERSIZE DIAMETER AND THREAD, AND UPON FRONT SEAT TRACK ANCHOR BOLT INSTALLATION, THE THREADS MAY HAVE BEEN STRIPPED.
-
FORD RANCHERO 1979
THE STEERING GEARS ON THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH IMPROPERLY MANUFACTURED SECTOR SHAFTS FROM WHICH THE THREADED PORTIONS OF THE SHAFTS MAY FRACTURE AND SEPARATE. SHOULD THE SECTOR SHAFT FRACTURE, THE PITMAN ARM MAY DISENGAGE FROM THE SPLINED PORTION OF THE SECTOR SHAFT.
-
FORD RANCHERO 1979
DUE TO AN ERROR IN THE VEHICLE ASSEMBLY COMPUTER BROADCAST PROGRAM, THE INVOLVED VEHICLES WERE EQUIPPED WITH 14X5.5 INCH WHEEL RIMS WHICH WERE INTENDED FOR USE ON PASSENGER CARS. THE TIRES WERE NOT MARKED WITH THE INFORMATION SPECIFIED BY FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 120, TIRE SELECTION AND RIMS FOR MOTOR VEHICLES OTHER THAN PASSENGER CARS. AS A RESULT, A NON-COMPLIANCE EXISTS TO THIS STANDARD.
-
FORD RANCHERO 1977
THE INVOLVED VEHICLES MAY EXPERIENCE FUEL LEAKAGE AT THE RUBBER HOSE CONNECTING THE FUEL INLET TUBE TO THE CARBURETOR FILTER. THIS LEAKAGE CONDITION IS DUE TO INSUFFICIENT INSERTION OF THE FUEL TUBE INTO THE HOSE OR IMPROPER POSITIONING OF THE HOSE CLAMP, CAUSING THE CLAMP TO BE CRIMPED DIRECTLY OVER THE FUEL TUBE BEAD.
-
FORD RANCHERO 1972
SEVEN-BLADE COOLING FANS INSTALLED ON THE INVOLVED VEHICLES MAY BE SUBJECT TO FATIGUE CRACKING OF THE BLADES DUE TO STRESSES GENERATED DURING NORMAL VEHICLE OPERATION.
-
FORD RANCHERO 1976
-
FORD RANCHERO 1975
-
FORD RANCHERO 1975
-
FORD RANCHERO 1974
-
FORD RANCHERO 1973
-
FORD RANCHERO 1973
-
FORD RANCHERO 1973
-
FORD RANCHERO 1973
-
FORD RANCHERO 1972
-
FORD RANCHERO 1971
THE SHOULDER BELT PIN CONNECTOR PLASTIC SLEEVES WHICH WERE INJECTION MOLDED CAN HAVE SURFACE IMPERFECTIONS OR DISCONTINUITIES AT THE POINT AT WHICH THERMAL PLASTIC IS INJECTED INTO MOLD AND WHERE FLOW DIVERGES TO FILL BOTH SIDES OF THE RING. IF THE CONDITION EXISTS AND THE SLEEVE BREAKS AWAY FROM THE PIN, THE SHOULDER BELT WILL NOT REMAIN ENGAGED TO THE SEAT BELT BUCKLE.
-
FORD RANCHERO 1970
THE SHOULDER BELT PIN CONNECTOR PLASTIC SLEEVES WHICH WERE INJECTION MOLDED CAN HAVE SURFACE IMPERFECTIONS OR DISCONTINUITIES AT THE POINT AT WHICH THERMAL PLASTIC IS INJECTED INTO MOLD AND WHERE FLOW DIVERGES TO FILL BOTH SIDES OF THE RING. IF THE CONDITION EXISTS AND THE SLEEVE BREAKS AWAY FROM THE PIN, THE SHOULDER BELT WILL NOT REMAIN ENGAGED TO THE SEAT BELT BUCKLE.
-
FORD RANCHERO 1972
-
FORD RANCHERO 1968