NISSAN FRONTIER
-
NISSAN FRONTIER 1998
CERTAIN PRO-A MOTORS CORNER LAMPS, TURN SIGNALS, AND HEADLIGHTS SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES LISTED ABOVE. SOME COMBINATION LAMPS THAT ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
-
NISSAN FRONTIER 2004
CERTAIN ANZO COMBINATION HEADLAMP ASSEMBLIES SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES. SOME COMBINATION LAMPS ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS WHICH FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
-
NISSAN FRONTIER 2003
CERTAIN ANZO COMBINATION HEADLAMP ASSEMBLIES SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES. SOME COMBINATION LAMPS ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS WHICH FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
-
NISSAN FRONTIER 2002
CERTAIN ANZO COMBINATION HEADLAMP ASSEMBLIES SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES. SOME COMBINATION LAMPS ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS WHICH FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
-
NISSAN FRONTIER 2001
CERTAIN ANZO COMBINATION HEADLAMP ASSEMBLIES SOLD AS REPLACEMENT LAMPS FOR USE ON CERTAIN PASSENGER VEHICLES. SOME COMBINATION LAMPS ARE NOT EQUIPPED WITH AMBER SIDE REFLECTORS WHICH FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 108, LAMPS, REFLECTIVE DEVICES, AND ASSOCIATED EQUIPMENT.
-
NISSAN FRONTIER 2003
ON CERTAIN PICKUP TRUCKS EQUIPPED WITH SIX CYLINDER ENGINES AND SPORT UTILITY VEHICLES EQUIPPED WITH FOUR OR SIX CYLINDER ENGINES, THE FUEL PUMP TERMINAL ON THE FUEL-SENDING UNIT CAN DEVELOP A CRACK IN THE PLASTIC MOLDING. THIS CAN CAUSE THE TERMINAL STRIP TO CORRODE UNDER SOME ENVIRONMENTAL CONDITIONS.
-
NISSAN FRONTIER 2002
ON CERTAIN PICKUP TRUCKS EQUIPPED WITH SIX CYLINDER ENGINES AND SPORT UTILITY VEHICLES EQUIPPED WITH FOUR OR SIX CYLINDER ENGINES, THE FUEL PUMP TERMINAL ON THE FUEL-SENDING UNIT CAN DEVELOP A CRACK IN THE PLASTIC MOLDING. THIS CAN CAUSE THE TERMINAL STRIP TO CORRODE UNDER SOME ENVIRONMENTAL CONDITIONS.
-
NISSAN FRONTIER 2001
ON CERTAIN PICKUP TRUCKS EQUIPPED WITH SIX CYLINDER ENGINES AND SPORT UTILITY VEHICLES EQUIPPED WITH FOUR OR SIX CYLINDER ENGINES, THE FUEL PUMP TERMINAL ON THE FUEL-SENDING UNIT CAN DEVELOP A CRACK IN THE PLASTIC MOLDING. THIS CAN CAUSE THE TERMINAL STRIP TO CORRODE UNDER SOME ENVIRONMENTAL CONDITIONS.
-
NISSAN FRONTIER 2000
ON CERTAIN PICKUP TRUCKS EQUIPPED WITH SIX CYLINDER ENGINES AND SPORT UTILITY VEHICLES EQUIPPED WITH FOUR OR SIX CYLINDER ENGINES, THE FUEL PUMP TERMINAL ON THE FUEL-SENDING UNIT CAN DEVELOP A CRACK IN THE PLASTIC MOLDING. THIS CAN CAUSE THE TERMINAL STRIP TO CORRODE UNDER SOME ENVIRONMENTAL CONDITIONS.
-
NISSAN FRONTIER 1999
ON CERTAIN PICKUP TRUCKS EQUIPPED WITH SIX CYLINDER ENGINES AND SPORT UTILITY VEHICLES EQUIPPED WITH FOUR OR SIX CYLINDER ENGINES, THE FUEL PUMP TERMINAL ON THE FUEL-SENDING UNIT CAN DEVELOP A CRACK IN THE PLASTIC MOLDING. THIS CAN CAUSE THE TERMINAL STRIP TO CORRODE UNDER SOME ENVIRONMENTAL CONDITIONS.
-
NISSAN FRONTIER 2003
ON CERTAIN SPORT UTILITY VEHICLES EQUIPPED WITH A V6 ENGINE, AN INCORRECT SIZE WHEEL RIM FOR THE SPARE TIRE WAS PROVIDED IN THESE VEHICLES. THE WHEEL RIM DOES NOT FIT PROPERLY AS A REPLACEMENT FOR A FRONT WHEEL.
-
NISSAN FRONTIER 2001
ON CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES, THE FUEL TANK INLET SHUTTER VALVE DOES NOT MEET THE SEALING PERFORMANCE SPECIFICATION.
-
NISSAN FRONTIER 2002
ON CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES EQUIPPED WITH A SUPERCHARGER, UNDER CERTAIN CONDITIONS, SUCH AS FULL THROTTLE IN LOW GEAR WHEN THE ENGINE IS NOT FULLY WARMED UP AND AT COLD AMBIENT TEMPERATURE, THE AMOUNT OF INTAKE AIR FLOW THROUGH THE AIR FLOW METER MAY EXCEED THE MAXIMUM PRESET DIAGNOSIS LIMIT VALUE.
-
NISSAN FRONTIER 2003
ON CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES, WATER MAY ENTER THE REAR AXLE HOUSING DUE TO INADEQUATE SEALING OF THE ANTI-LOCK BRAKING SYSTEM (ABS) SENSOR.
-
NISSAN FRONTIER 2002
ON CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES, WATER MAY ENTER THE REAR AXLE HOUSING DUE TO INADEQUATE SEALING OF THE ANTI-LOCK BRAKING SYSTEM (ABS) SENSOR.
-
NISSAN FRONTIER 2001
ON CERTAIN PICKUP TRUCKS AND SPORT UTILITY VEHICLES, WATER MAY ENTER THE REAR AXLE HOUSING DUE TO INADEQUATE SEALING OF THE ANTI-LOCK BRAKING SYSTEM (ABS) SENSOR.
-
NISSAN FRONTIER 2000
VEHICLE DESCRIPTION: PICKUP TRUCKS AND SPORT UTILITY VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS FAIL TO COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 102, TRANSMISSION SHIFT LEVER SEQUENCE, STARTER INTERLOCK, AND TRANSMISSION BRAKING EFFECT. THESE VEHICLES COULD HAVE A SHIFT CABLE LOCK PLATE THAT IS TOO BRITTLE AND CAN BREAK. THE GEAR SHIFT LEVER AND THE PRNDL INDICATOR MAY MOVE, BUT THE TRANSMISSION WILL NOT SHIFT OUT OF THE PARK POSITION. OVER A PERIOD OF TIME, THE TRANSMISSION COULD SHIFT OUT OF THE PARK POSITION, BUT THE GEAR INDICATED ON THE DISPLAY MAY DIFFER FROM THE GEAR ENGAGED IN THE TRANSMISSION.
-
NISSAN FRONTIER 2000
VEHICLE DESCRIPTION: MINIVANS AND LIGHT DUTY TRUCKS. THE TAIL LIGHT SOCKET MAY HAVE BEEN IMPROPERLY MOLDED, RESULTING IN THE LOCKING TAB HAVING INSUFFICIENT FORCE TO RETAIN THE BULB.
-
NISSAN FRONTIER 1999
VEHICLE DESCRIPTION: MINIVANS AND LIGHT DUTY TRUCKS. THE TAIL LIGHT SOCKET MAY HAVE BEEN IMPROPERLY MOLDED, RESULTING IN THE LOCKING TAB HAVING INSUFFICIENT FORCE TO RETAIN THE BULB.
-
NISSAN FRONTIER 1998
VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER TRUCKS EQUIPPED WITH AUTOMATIC TRANSMISSIONS. A SECURING PIN INSIDE THE AUTOMATIC TRANSMISSION CONTROL DEVICE ASSEMBLY CAN COME LOOSE ALLOWING THE SHIFT LEVER TO BE INADVERTENTLY MOVED OUT OF THE PARK POSITION WITH THE KEY IN THE IGNITION.
-
NISSAN FRONTIER 1998
VEHICLE DESCRIPTION: LIGHT DUTY PASSENGER TRUCKS EQUIPPED WITH BUCKET SEATS. IN CERTAIN FRONTAL CRASHES, THE FRONT SEAT BELT CAN SLIP BETWEEN THE SEAT BOTTOM FINISHER AND THE SEAT BACK PLASTIC RECLINER HANDLE WHERE IT CAN BE CUT BY THE SHARP EDGE OF THE METAL PORTION OF THE RECLINER LEVER.