Ford F800
-
FORD F800 1979
CERTAIN FEDERAL-MOGUL AFTERMARKET FUEL PUMPS SOLD UNDER THE BRAND NAMES OF CARTER, ACCUFLOW, NAPA, TRUFLOW, PARTS DEPO, AND PARTS MASTER, SHIPPED BETWEEN AUGUST 2006 AND JULY 2007 FOR USE ON THE VEHICLES LISTED ABOVE. THE FUEL PUMP DIAPHRAGM IN CERTAIN PRODUCTION RUNS MAY HAVE BEEN IMPROPERLY INSTALLED OR INADEQUATELY TESTED WHICH MAY CAUSE THE FUEL PUMP TO LEAK.
-
FORD F800 1998
VEHICLE DESCRIPTION: MEDIUM DUTY TRUCKS AND CHASSIS-CABS. AN AUTOMATIC LOCKING FRONT WHEEL BEARING ADJUSTING NUT WAS DAMAGED DURING INSTALLATION OR REMOVAL BY INCORRECT TOOLS OR AN INCORRECT TORQUE SPECIFICATION WAS USED.
-
FORD F800 1998
VEHICLE DESCRIPTION: MEDIUM DUTY TRUCKS AND SCHOOL BUS CHASSIS-COWLS EQUIPPED WITH AUTOMATIC TRANSMISSIONS. THE WELDS THAT ATTACH THE KEY TO THE TOP OF THE STEERING COLUMN MOUNTED AUTOMATIC TRANSMISSION SHIFT LINKAGE MAY NOT ADEQUATELY RETAIN THE KEY, ALLOWING THE TRANSMISSION TO BE IN A GEAR OTHER THAN THAT INDICATED ON THE PRNDL, OR IN SOME CASES, RNDL.
-
FORD F800 1994
THE HAND THROTTLE CABLE CAN WEAR THE BRASS SWIVEL BLOCK ON THE GOVERNOR LEVER THROUGH WHICH IT PASSES.
-
FORD F800 1995
THE HAND THROTTLE CABLE CAN WEAR THE BRASS SWIVEL BLOCK ON THE GOVERNOR LEVER THROUGH WHICH IT PASSES.
-
FORD F800 1993
THE HAND THROTTLE CABLE CAN WEAR THE BRASS SWIVEL BLOCK ON THE GOVERNOR LEVER THROUGH WHICH IT PASSES.
-
FORD F800 1995
AIR SYSTEM BLOCKAGE IN THE AIR DRYER OCCURS DEGRADING THE MOISTURE REMOVING CAPABILITIES OF THE DRYER WHEN THE VEHICLE IS OPERATED IN A COLD ENVIRONMENT AND MOISTURE ACCUMULATES AND FREEZES IN THE AIR DRYER OR IN THE LINE BETWEEN THE DRYER AND THE AIR SYSTEM RESERVOIR. THE AIR DRYER CAN BECOME OVERPRESSURIZED CAUSING THE AIR DRYER CARTRIDGE TO SEPARATE FROM THE MOUNTING BASE.
-
FORD F800 1993
AIR SYSTEM BLOCKAGE IN THE AIR DRYER OCCURS DEGRADING THE MOISTURE REMOVING CAPABILITIES OF THE DRYER WHEN THE VEHICLE IS OPERATED IN A COLD ENVIRONMENT AND MOISTURE ACCUMULATES AND FREEZES IN THE AIR DRYER OR IN THE LINE BETWEEN THE DRYER AND THE AIR SYSTEM RESERVOIR. THE AIR DRYER CAN BECOME OVERPRESSURIZED CAUSING THE AIR DRYER CARTRIDGE TO SEPARATE FROM THE MOUNTING BASE.
-
FORD F800 1994
AIR SYSTEM BLOCKAGE IN THE AIR DRYER OCCURS DEGRADING THE MOISTURE REMOVING CAPABILITIES OF THE DRYER WHEN THE VEHICLE IS OPERATED IN A COLD ENVIRONMENT AND MOISTURE ACCUMULATES AND FREEZES IN THE AIR DRYER OR IN THE LINE BETWEEN THE DRYER AND THE AIR SYSTEM RESERVOIR. THE AIR DRYER CAN BECOME OVERPRESSURIZED CAUSING THE AIR DRYER CARTRIDGE TO SEPARATE FROM THE MOUNTING BASE.
-
FORD F800 1994
A CONNECTOR IN THE WIRING WHERE THE TILT HOOD MOUNTED LAMPS ATTACH TO THE VEHICLE WIRING HARNESS WAS BUILT WITHOUT SEALING PLUGS. MOISTURE, ROAD SALT OR OTHER CONTAMINANTS CAN ENTER THE CONNECTION RESULTING IN CROSSED CIRCUITS, SHORTS OR CORROSION OF THE WIRING OF THE CONNECTOR.
-
FORD F800 1995
A CONNECTOR IN THE WIRING WHERE THE TILT HOOD MOUNTED LAMPS ATTACH TO THE VEHICLE WIRING HARNESS WAS BUILT WITHOUT SEALING PLUGS. MOISTURE, ROAD SALT OR OTHER CONTAMINANTS CAN ENTER THE CONNECTION RESULTING IN CROSSED CIRCUITS, SHORTS OR CORROSION OF THE WIRING OF THE CONNECTOR.
-
FORD F800 1995
THE DRAG LINK INSTALLED CAN CONTACT THE FRONT AXLE I-BEAM UNDER CERTAIN EXTREME CONDITIONS. THIS DRAG LINK WAS NOT INTENDED TO BE INSTALLED ON LOW PROFILE VEHICLES.
-
FORD F800 1995
THE VEHICLES WERE MANUFACTURED WITHOUT SEPARATE ABS INDICATOR LAMPS. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO. 105, HYDRAULIC BRAKE SYSTEMS.
-
FORD F800 1992
AS A RESULT OF INHERENT VIBRATION IN THESE ENGINES, THE THROTTLE RETURN SPRINGS CAN FRACTURE.
-
FORD F800 1993
AS A RESULT OF INHERENT VIBRATION IN THESE ENGINES, THE THROTTLE RETURN SPRINGS CAN FRACTURE.
-
FORD F800 1993
-
FORD F800 1992
WATER CAN ENTER THE DOOR LATCH RELEASE CABLE. IF THE VEHICLE IS OPERATED IN BELOW FREEZING TEMPERATURES, THE WATER IN THE DOOR LATCH RELEASE CABLE CAN FREEZE AND CAUSE THE LATCH MECHANISM TO MALFUNCTION.
-
FORD F800 1991
THE THROTTLE CABLE WHICH RUNS FROM THE ACCELERATOR TO THE GOVERNOR ASSEMBLY HOUSING MAY HAVE BEEN KINKED DURING ASSEMBLY, CAUSING EXCESSIVE WEAR OF THE CABLE HOUSING INNER LINING. THIS COULD RESULT IN EITHER FRACTURE OR STICKING OF THE CABLE.
-
FORD F800 1990
THE THROTTLE CABLE WHICH RUNS FROM THE ACCELERATOR TO THE GOVERNOR ASSEMBLY HOUSING MAY HAVE BEEN KINKED DURING ASSEMBLY, CAUSING EXCESSIVE WEAR OF THE CABLE HOUSING INNER LINING. THIS COULD RESULT IN EITHER FRACTURE OR STICKING OF THE CABLE.
-
FORD F800 1984
THE INVOLVED VEHICLES WERE PRODUCED WITH HYDRAULIC BRAKE BOOSTER SUPPLY HOSES THAT ARE LOCATED TOO CLOSE TO THE ENGINE EXHAUST MANIFOLD AND MAY CHAFE AND DEVELOP HEAT DAMAGE DURING VEHICLE OPERATION. CHAFING AND HEAT INDUCED DETERIORATION OF A HOSE DUE TO DIRECT CONTACT WITH THE MANIFOLD MAY CAUSE THE HOSE TO WEAR. A SUBSEQUENT RUPTURE WILL RESULT IN PUMP FLUID LOSS.
-
FORD F800 1983
TWO-INCH SPACERS SPECIFIED FOR INSTALLATION BETWEEN THE FRONT AXLES AND EACH FRONT SPRING ASSEMBLY WERE OMITTED DURING MANUFACTURE. UNDER CERTAIN TURNING AND BOUNCING CONDITIONS, A FRONT TIRE COULD CONTACT ADJACENT VEHICLE COMPONENTS, RESULTING IN A POSSIBLE SEPARATION OF THE DRAG LINK TO STEERING ARM BALLJOINT OR LOSS OF TIRE PRESSURE.
-
FORD F800 1983
ON THE AFFECTED VEHICLES, THE WIRING ASSEMBLY TO THE FLOOR MOUNTED HEADLAMP DIMMER SWITCH MAY BE TOO TIGHT; SHOULD WIRES DISCONNECT, THE HEADLIGHTS WILL NOT OPERATE.
-
FORD F800 1980
THE MASTER CYLINDER TO CHASIS BRAKE TUBE AND HOSE ASSEMBLIES MAY HAVE BEEN MOVED FROM THEIR INTENDED POSITION, WHICH COULD ALLOW CHAFING AGAINST UNDERBODY COMPONENTS. CHAFING PROMOTES WEAR OF THE BRAKE TUBE AND HOSE ASSEMBLY AND COULD CAUSE A LOSS OF BRAKE FLUID.
-
FORD F800 1981
THE MASTER CYLINDER TO CHASIS BRAKE TUBE AND HOSE ASSEMBLIES MAY HAVE BEEN MOVED FROM THEIR INTENDED POSITION, WHICH COULD ALLOW CHAFING AGAINST UNDERBODY COMPONENTS. CHAFING PROMOTES WEAR OF THE BRAKE TUBE AND HOSE ASSEMBLY AND COULD CAUSE A LOSS OF BRAKE FLUID.
-
FORD F800 1981
THE INVOLVED VEHICLES WERE ASSEMBLED WITH THE LEFT FRONT BRAKE TUBE RETAINING CLIP MISSING. THE ABSENCE OF A RETAINING CLIP MAY ALLOW THE BRAKE TUBE TO RUB AGAINST THE SHOCK ABSORBER, CAUSING WEAR ON THE TUBE AND, EVENTUALLY, LOSS OF BRAKE FLUID.
-
FORD F800 1980
THE PRIMARY CIRCUIT CONNECTION, WHICH PROVIDES PRIMARY ELECTRICAL POWER TO THE ENGINE, COULD DETERIORATE DUE TO HIGH CURRENT DRAW PRODUCED BY BUILDER-INSTALLED EQUIPMENT.
-
FORD F800 1981
THE PRIMARY CIRCUIT CONNECTION, WHICH PROVIDES PRIMARY ELECTRICAL POWER TO THE ENGINE, COULD DETERIORATE DUE TO HIGH CURRENT DRAW PRODUCED BY BUILDER-INSTALLED EQUIPMENT.
-
FORD F800 1979
THE AIR BRAKE LINES MAY BE ROUTED TOO CLOSE TO THE EXHAUST MUFFLER. BECAUSE THE AIR BRAKE LINES ARE MADE OF NYLON MATERIAL, HEAT FROM THE EXHAUST MUFFLER CAN WEAKEN THE BRAKE LINE TUBES, POSSIBLY CAUSING THEM TO RUPTURE. TUBE RUPTURE COULD RESULT IN LOSS OF AIR IN THE SECONDARY AIR BRAKE SYSTEM.