vin-number

MACK R

MACK R 1990

THE STEERING ARM CAN DEVELOP CRACKS CAUSING THE LEVER TO BREAK WITHOUT WARNING.
MACK R 1991

FUEL INJECTION SYSTEM RECONFIGURATION TO COMPLY WITH ENGINE EMISSION STANDARDS CAUSE HIGHER ENGINE VIBRATION LEVELS WHICH LEAD TO EARLY WEAR AND COMPLETE FAILURE OF THE SECONDARY THROTTLE RETURN MECHANISM.
MACK R 1990

FUEL INJECTION SYSTEM RECONFIGURATION TO COMPLY WITH ENGINE EMISSION STANDARDS CAUSE HIGHER ENGINE VIBRATION LEVELS WHICH LEAD TO EARLY WEAR AND COMPLETE FAILURE OF THE SECONDARY THROTTLE RETURN MECHANISM.
MACK R 1989

FUEL INJECTION SYSTEM RECONFIGURATION TO COMPLY WITH ENGINE EMISSION STANDARDS CAUSE HIGHER ENGINE VIBRATION LEVELS WHICH LEAD TO EARLY WEAR AND COMPLETE FAILURE OF THE SECONDARY THROTTLE RETURN MECHANISM.
MACK R 1987

FUEL INJECTION SYSTEM RECONFIGURATION TO COMPLY WITH ENGINE EMISSION STANDARDS CAUSE HIGHER ENGINE VIBRATION LEVELS WHICH LEAD TO EARLY WEAR AND COMPLETE FAILURE OF THE SECONDARY THROTTLE RETURN MECHANISM.
MACK R 1988

FUEL INJECTION SYSTEM RECONFIGURATION TO COMPLY WITH ENGINE EMISSION STANDARDS CAUSE HIGHER ENGINE VIBRATION LEVELS WHICH LEAD TO EARLY WEAR AND COMPLETE FAILURE OF THE SECONDARY THROTTLE RETURN MECHANISM.
MACK R 1992

FUEL INJECTION SYSTEM RECONFIGURATION TO COMPLY WITH ENGINE EMISSION STANDARDS CAUSE HIGHER ENGINE VIBRATION LEVELS WHICH LEAD TO EARLY WEAR AND COMPLETE FAILURE OF THE SECONDARY THROTTLE RETURN MECHANISM.
MACK R 1989

A TOLERANCE MISMATCH IN THE CRANK ASSEMBLY OF THE BOSCH WINDSHIELD WIPER MOTOR COULD CAUSE INSTANTANEOUS SEPARATION OF THE CRANK FROM THE LINKAGE ASSEMBLY IN THE LEFT HAND CONTROL ARM ASSEMBLY; THIS WOULD MAKE THE SYSTEM INOPERABLE.
MACK R 1989

INTERFERENCE BETWEEN STEERING GEAR SECTOR SHAFT AND THE FRAME RAIL THROUGH HOLE CAN CAUSE SECTOR SHAFT WEAR AND CAN WEAKEN SHAFT CAUSE IT TO BREAK.
MACK R 1984

DUE TO IMPROPER AND INADEQUATE WELDING PRACTICES, THE FIFTH WHEEL ON THE INVOLVED VEHICLES IS DEFECTIVE. FRAME MOUNTED SUPPORTS MAY HAVE INCOMPLETE OR POOR QUALITY WELDS. THE WELDS COULD SUBSEQUENTLY FAIL ALLOWING SEPARATION OF THE TRACTOR FROM THE TRAILER.
MACK R 1983

DUE TO IMPROPER AND INADEQUATE WELDING PRACTICES, THE FIFTH WHEEL ON THE INVOLVED VEHICLES IS DEFECTIVE. FRAME MOUNTED SUPPORTS MAY HAVE INCOMPLETE OR POOR QUALITY WELDS. THE WELDS COULD SUBSEQUENTLY FAIL ALLOWING SEPARATION OF THE TRACTOR FROM THE TRAILER.
MACK R 1982

DUE TO IMPROPER AND INADEQUATE WELDING PRACTICES, THE FIFTH WHEEL ON THE INVOLVED VEHICLES IS DEFECTIVE. FRAME MOUNTED SUPPORTS MAY HAVE INCOMPLETE OR POOR QUALITY WELDS. THE WELDS COULD SUBSEQUENTLY FAIL ALLOWING SEPARATION OF THE TRACTOR FROM THE TRAILER.
MACK R 1979

THE SPRING SEAT PLATE, LOCATED BETWEEN THE AXLE HOUSING AND THE SUSPENSION SPRINGS, MAY DEFORM DUE TO SPRING BENDING. AS A RESULT, THE CLAMPING FORCE IN THE ASSEMBLY MAY BE REDUCED. LOSS OF CLAMPING FORCE COULD CAUSE SPRING FAILURE AND THE AXLE WILL DISLOCATE. ALSO, THE TIRE COULD COME INTO CONTACT WITH THE SPRING.
MACK R 1979

THE PINCH BOLT HOLE CENTER TO STEERING GEAR INPUT SHAFT ON THE LOWER YOKE DIMENSION EXCEEDS SPECIFICATIONS. IF THE PINCH BOLT BECOMES LOOSE, IT WILL NOT ENGAGE THE STEERING GEAR INPUT SHAFT NOTCH AND THE SHAFT COULD SLIP OFF.
MACK R 1977

IN THE EVENT OF TURBOCHARGER COMPRESSOR WHEEL FAILURE, ONE OR MORE OF THE FOUR CAPSCREWS THAT HOLD THE TURBOCHARGER TOGETHER MAY BE STRUCK BY PARTS OF THE COMPRESSOR WHEEL, RESULTING IN THE CAPSCREWS BEING DAMAGED. IF THESE CAPSCREWS ARE DAMAGED TO THE POINT THAT THEY ALLOW THE COMPRESSOR BACK PLATE TO DISLOCATE FROM THE TURBOCHARGER BEARING HOUSING, ENGINE LUBRICATING OIL MAY BE ALLOWED TO ESCAPE UNDER PRESSURE, CONTACTING THE ENGINE EXHAUST MANIFOLD SECTIONS OR TURBOCHARGER TURBINE HOUSING.
MACK R 1979

IN THE EVENT OF TURBOCHARGER COMPRESSOR WHEEL FAILURE, ONE OR MORE OF THE FOUR CAPSCREWS THAT HOLD THE TURBOCHARGER TOGETHER MAY BE STRUCK BY PARTS OF THE COMPRESSOR WHEEL, RESULTING IN THE CAPSCREWS BEING DAMAGED. IF THESE CAPSCREWS ARE DAMAGED TO THE POINT THAT THEY ALLOW THE COMPRESSOR BACK PLATE TO DISLOCATE FROM THE TURBOCHARGER BEARING HOUSING, ENGINE LUBRICATING OIL MAY BE ALLOWED TO ESCAPE UNDER PRESSURE, CONTACTING THE ENGINE EXHAUST MANIFOLD SECTIONS OR TURBOCHARGER TURBINE HOUSING.
MACK R 1978

IN THE EVENT OF TURBOCHARGER COMPRESSOR WHEEL FAILURE, ONE OR MORE OF THE FOUR CAPSCREWS THAT HOLD THE TURBOCHARGER TOGETHER MAY BE STRUCK BY PARTS OF THE COMPRESSOR WHEEL, RESULTING IN THE CAPSCREWS BEING DAMAGED. IF THESE CAPSCREWS ARE DAMAGED TO THE POINT THAT THEY ALLOW THE COMPRESSOR BACK PLATE TO DISLOCATE FROM THE TURBOCHARGER BEARING HOUSING, ENGINE LUBRICATING OIL MAY BE ALLOWED TO ESCAPE UNDER PRESSURE, CONTACTING THE ENGINE EXHAUST MANIFOLD SECTIONS OR TURBOCHARGER TURBINE HOUSING.
MACK R 1977

AN IMPROPER PINCH BOLT AND NUT MAY HAVE BEEN USED IN THE CLAMPING OF THE STEERING SHAFT TO THE STEERING GEAR INPUT SHAFT. DUE TO CLAMPING FORCE LOADS APPLIED AT THE BOLT, THE NUT COULD YIELD, RESULTING IN LOOSENESS OF THE INPUT SHAFT YOKE. SHOULD THIS CONDITION GO UNNOTICED, SPLINE WEAR COULD CAUSE SHAFT SEPARATION.
MACK R 1978

AN IMPROPER PINCH BOLT AND NUT MAY HAVE BEEN USED IN THE CLAMPING OF THE STEERING SHAFT TO THE STEERING GEAR INPUT SHAFT. DUE TO CLAMPING FORCE LOADS APPLIED AT THE BOLT, THE NUT COULD YIELD, RESULTING IN LOOSENESS OF THE INPUT SHAFT YOKE. SHOULD THIS CONDITION GO UNNOTICED, SPLINE WEAR COULD CAUSE SHAFT SEPARATION.
MACK R 1977

A CASTING DEFICIENCY EXISTS IN THE LOWER SECTION OF THE CAPS RESULTING IN A REDUCTION IN THE THICKNESS OF THE MATERIAL. FAILURE OF A CAP CAN ALLOW THE END OF THE REAR SPRING TO DETACH FROM THE AXLE HOUSING.
MACK R 1978

A CASTING DEFICIENCY EXISTS IN THE LOWER SECTION OF THE CAPS RESULTING IN A REDUCTION IN THE THICKNESS OF THE MATERIAL. FAILURE OF A CAP CAN ALLOW THE END OF THE REAR SPRING TO DETACH FROM THE AXLE HOUSING.
MACK R 1978

THE STEEL BRACKETS ON THE SUSPENSION BEAM WERE FOUND TO BE DEFICIENT DUE TO EXCESSIVE SHRINKAGE AND LOW MECHANICAL PROPERTIES. FAILURE OF ONE OR BOTH OF THESE BRACKETS COULD CAUSE A SEPARATION OF THE AXLE HOUSING FROM THE SUSPENSION.
MACK R 1977

DELAYS OF UP TO ABOUT 2 SECONDS MAY EXIST IN THE BRAKE APPLICATION TIMES TO THE BRAKES ON THE BOGIE AXLES IN THE PRESENCE OF CERTAIN TYPES OF WHEEL SPEED SENSOR SIGNAL DISCONTINUITIES OR DISTORTIONS THAT MAY OCCUR AS A RESULT OF SENSOR WIRE FAILURE. THIS CONSTITUTES A NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS.
MACK R 1978

DELAYS OF UP TO ABOUT 2 SECONDS MAY EXIST IN THE BRAKE APPLICATION TIMES TO THE BRAKES ON THE BOGIE AXLES IN THE PRESENCE OF CERTAIN TYPES OF WHEEL SPEED SENSOR SIGNAL DISCONTINUITIES OR DISTORTIONS THAT MAY OCCUR AS A RESULT OF SENSOR WIRE FAILURE. THIS CONSTITUTES A NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS.
MACK R 1971

DEFICIENCIES, IN THE FORM OF FORGING LAPS, CRACKS AND EXCESSIVE DECARBURIZATION DURING HEAT TREATMENT, EXIST IN THE STEERING KNUCKLES. STRESSES IMPOSED WITH INTEGRAL HYDRAULIC POWER STEERING MAY LEAD TO A FAILURE IN THE AREA OF THE STEERING ARM ATTACHING BOSS. THIS TYPE OF FAILURE WOULD CAUSE LOSS OF STEERING CONTROL.
MACK R 1972

DEFICIENCIES, IN THE FORM OF FORGING LAPS, CRACKS AND EXCESSIVE DECARBURIZATION DURING HEAT TREATMENT, EXIST IN THE STEERING KNUCKLES. STRESSES IMPOSED WITH INTEGRAL HYDRAULIC POWER STEERING MAY LEAD TO A FAILURE IN THE AREA OF THE STEERING ARM ATTACHING BOSS. THIS TYPE OF FAILURE WOULD CAUSE LOSS OF STEERING CONTROL.
MACK R 1973

DEFICIENCIES, IN THE FORM OF FORGING LAPS, CRACKS AND EXCESSIVE DECARBURIZATION DURING HEAT TREATMENT, EXIST IN THE STEERING KNUCKLES. STRESSES IMPOSED WITH INTEGRAL HYDRAULIC POWER STEERING MAY LEAD TO A FAILURE IN THE AREA OF THE STEERING ARM ATTACHING BOSS. THIS TYPE OF FAILURE WOULD CAUSE LOSS OF STEERING CONTROL.
MACK R 1974

DEFICIENCIES, IN THE FORM OF FORGING LAPS, CRACKS AND EXCESSIVE DECARBURIZATION DURING HEAT TREATMENT, EXIST IN THE STEERING KNUCKLES. STRESSES IMPOSED WITH INTEGRAL HYDRAULIC POWER STEERING MAY LEAD TO A FAILURE IN THE AREA OF THE STEERING ARM ATTACHING BOSS. THIS TYPE OF FAILURE WOULD CAUSE LOSS OF STEERING CONTROL.
MACK R 1976

AN AXLE NO BRAKE CONDITION COULD RESULT FROM AN EATON CONTROLLER INTERNAL ELECTRICAL MALFUNCTION. THIS CONDITION MAY CAUSE THE ANTI-WHEEL LOCK VALVE SOLENOID TO BE CONTINUOUSLY ENERGIZED AND PREVENT THE BRAKES FROM BEING APPLIED ON ONE OF THE AXLES. AS A RESULT, THE ANTI-WHEEL LOCK WARNING LAMP IS NOT ACTIVATED.
MACK R 1974

AN AXLE NO BRAKE CONDITION COULD RESULT FROM AN EATON CONTROLLER INTERNAL ELECTRICAL MALFUNCTION. THIS CONDITION MAY CAUSE THE ANTI-WHEEL LOCK VALVE SOLENOID TO BE CONTINUOUSLY ENERGIZED AND PREVENT THE BRAKES FROM BEING APPLIED ON ONE OF THE AXLES. AS A RESULT, THE ANTI-WHEEL LOCK WARNING LAMP IS NOT ACTIVATED.