vin-number

MACK WL

MACK WL 1981

THE PITMAN ARM, A LEVER THAT TRANSMITS TURNING MOVEMENTS FROM THE STEERING GEAR TO THE STEERING LINKAGE, MAY LOOSEN OR BREAK AT ITS CONNECTION TO THE STEERING LINKAGE. THE FAILURE CAN PREVENT TURNING ATTEMPTS FROM HAVING ANY EFFECT. THE DEFECT IS CAUSED BY INCORRECT ASSEMBLY OF THE BALL STUD CONNECTION IN THE PITMAN ARM.
MACK WL 1980

THE PITMAN ARM, A LEVER THAT TRANSMITS TURNING MOVEMENTS FROM THE STEERING GEAR TO THE STEERING LINKAGE, MAY LOOSEN OR BREAK AT ITS CONNECTION TO THE STEERING LINKAGE. THE FAILURE CAN PREVENT TURNING ATTEMPTS FROM HAVING ANY EFFECT. THE DEFECT IS CAUSED BY INCORRECT ASSEMBLY OF THE BALL STUD CONNECTION IN THE PITMAN ARM.
MACK WL 1979

THE SPRING SEAT PLATE, LOCATED BETWEEN THE AXLE HOUSING AND THE SUSPENSION SPRINGS, MAY DEFORM DUE TO SPRING BENDING. AS A RESULT, THE CLAMPING FORCE IN THE ASSEMBLY MAY BE REDUCED. LOSS OF CLAMPING FORCE COULD CAUSE SPRING FAILURE AND THE AXLE WILL DISLOCATE. ALSO, THE TIRE COULD COME INTO CONTACT WITH THE SPRING.
MACK WL 1979

THE FLANGE HEAD PINCH BOLTS USED IN THE YOKES OF THE STEERING SHAFT ASSEMBLIES MAY HAVE BEEN OVERSTRESSED DUE TO THE BOLTS NOT BEING TIGHTENED TO SPECIFICATIONS. AS A RESULT, THE PINCH BOLTS COULD BREAK WHILE IN SERVICE.
MACK WL 1979

THE PITMAN ARM RETAINING NUT MAY NOT HAVE BEEN TORQUED TO MANUFACTURER SPECIFICATIONS. THIS COULD RESULT IN INADEQUATE RETENTION OF THE NUT AT THE OUTPUT SHAFT, ALLOWING THE PITMAN ARM TO BECOME LOOSE.
MACK WL 1977

THE PITMAN ARM RETAINING NUT MAY NOT HAVE BEEN TORQUED TO MANUFACTURER SPECIFICATIONS. THIS COULD RESULT IN INADEQUATE RETENTION OF THE NUT AT THE OUTPUT SHAFT, ALLOWING THE PITMAN ARM TO BECOME LOOSE.
MACK WL 1978

THE PITMAN ARM RETAINING NUT MAY NOT HAVE BEEN TORQUED TO MANUFACTURER SPECIFICATIONS. THIS COULD RESULT IN INADEQUATE RETENTION OF THE NUT AT THE OUTPUT SHAFT, ALLOWING THE PITMAN ARM TO BECOME LOOSE.
MACK WL 1977

IN THE EVENT OF TURBOCHARGER COMPRESSOR WHEEL FAILURE, ONE OR MORE OF THE FOUR CAPSCREWS THAT HOLD THE TURBOCHARGER TOGETHER MAY BE STRUCK BY PARTS OF THE COMPRESSOR WHEEL, RESULTING IN THE CAPSCREWS BEING DAMAGED. IF THESE CAPSCREWS ARE DAMAGED TO THE POINT THAT THEY ALLOW THE COMPRESSOR BACK PLATE TO DISLOCATE FROM THE TURBOCHARGER BEARING HOUSING, ENGINE LUBRICATING OIL MAY BE ALLOWED TO ESCAPE UNDER PRESSURE, CONTACTING THE ENGINE EXHAUST MANIFOLD SECTIONS OR TURBOCHARGER TURBINE HOUSING.
MACK WL 1978

IN THE EVENT OF TURBOCHARGER COMPRESSOR WHEEL FAILURE, ONE OR MORE OF THE FOUR CAPSCREWS THAT HOLD THE TURBOCHARGER TOGETHER MAY BE STRUCK BY PARTS OF THE COMPRESSOR WHEEL, RESULTING IN THE CAPSCREWS BEING DAMAGED. IF THESE CAPSCREWS ARE DAMAGED TO THE POINT THAT THEY ALLOW THE COMPRESSOR BACK PLATE TO DISLOCATE FROM THE TURBOCHARGER BEARING HOUSING, ENGINE LUBRICATING OIL MAY BE ALLOWED TO ESCAPE UNDER PRESSURE, CONTACTING THE ENGINE EXHAUST MANIFOLD SECTIONS OR TURBOCHARGER TURBINE HOUSING.
MACK WL 1979

IN THE EVENT OF TURBOCHARGER COMPRESSOR WHEEL FAILURE, ONE OR MORE OF THE FOUR CAPSCREWS THAT HOLD THE TURBOCHARGER TOGETHER MAY BE STRUCK BY PARTS OF THE COMPRESSOR WHEEL, RESULTING IN THE CAPSCREWS BEING DAMAGED. IF THESE CAPSCREWS ARE DAMAGED TO THE POINT THAT THEY ALLOW THE COMPRESSOR BACK PLATE TO DISLOCATE FROM THE TURBOCHARGER BEARING HOUSING, ENGINE LUBRICATING OIL MAY BE ALLOWED TO ESCAPE UNDER PRESSURE, CONTACTING THE ENGINE EXHAUST MANIFOLD SECTIONS OR TURBOCHARGER TURBINE HOUSING.
MACK WL 1977

DELAYS OF UP TO ABOUT 2 SECONDS MAY EXIST IN THE BRAKE APPLICATION TIMES TO THE BRAKES ON THE BOGIE AXLES IN THE PRESENCE OF CERTAIN TYPES OF WHEEL SPEED SENSOR SIGNAL DISCONTINUITIES OR DISTORTIONS THAT MAY OCCUR AS A RESULT OF SENSOR WIRE FAILURE. THIS CONSTITUTES A NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS.
MACK WL 1978

DELAYS OF UP TO ABOUT 2 SECONDS MAY EXIST IN THE BRAKE APPLICATION TIMES TO THE BRAKES ON THE BOGIE AXLES IN THE PRESENCE OF CERTAIN TYPES OF WHEEL SPEED SENSOR SIGNAL DISCONTINUITIES OR DISTORTIONS THAT MAY OCCUR AS A RESULT OF SENSOR WIRE FAILURE. THIS CONSTITUTES A NON-COMPLIANCE TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 121, AIR BRAKE SYSTEMS.
MACK WL 1977

THE POSSIBILITY EXISTS THAT THE ALUMINUM ENGINE REAR SUPPORT BRACKETS MAY FAIL DUE TO METAL FATIGUE. THIS TYPE OF FAILURE WOULD ALLOW THE ENGINE AND TRANSMISSION ASSEMBLY TO DISLOCATE DOWNWARD. THIS WILL RESULT IN THROTTLE CONTROL LOSS WITH THE ENGINE OPERATING CONTINUOUSLY IN THE MID TO UPPER RANGE OF THE GOVERNED SPEED RANGE.
MACK WL 1978

THE POSSIBILITY EXISTS THAT THE ALUMINUM ENGINE REAR SUPPORT BRACKETS MAY FAIL DUE TO METAL FATIGUE. THIS TYPE OF FAILURE WOULD ALLOW THE ENGINE AND TRANSMISSION ASSEMBLY TO DISLOCATE DOWNWARD. THIS WILL RESULT IN THROTTLE CONTROL LOSS WITH THE ENGINE OPERATING CONTINUOUSLY IN THE MID TO UPPER RANGE OF THE GOVERNED SPEED RANGE.
MACK WL 1975

THE POSSIBILITY EXISTS THAT THE ALUMINUM ENGINE REAR SUPPORT BRACKETS MAY FAIL DUE TO METAL FATIGUE. THIS TYPE OF FAILURE WOULD ALLOW THE ENGINE AND TRANSMISSION ASSEMBLY TO DISLOCATE DOWNWARD. THIS WILL RESULT IN THROTTLE CONTROL LOSS WITH THE ENGINE OPERATING CONTINUOUSLY IN THE MID TO UPPER RANGE OF THE GOVERNED SPEED RANGE.
MACK WL 1976

THE POSSIBILITY EXISTS THAT THE ALUMINUM ENGINE REAR SUPPORT BRACKETS MAY FAIL DUE TO METAL FATIGUE. THIS TYPE OF FAILURE WOULD ALLOW THE ENGINE AND TRANSMISSION ASSEMBLY TO DISLOCATE DOWNWARD. THIS WILL RESULT IN THROTTLE CONTROL LOSS WITH THE ENGINE OPERATING CONTINUOUSLY IN THE MID TO UPPER RANGE OF THE GOVERNED SPEED RANGE.
MACK WL 1974

AN AXLE NO BRAKE CONDITION COULD RESULT FROM AN EATON CONTROLLER INTERNAL ELECTRICAL MALFUNCTION. THIS CONDITION MAY CAUSE THE ANTI-WHEEL LOCK VALVE SOLENOID TO BE CONTINUOUSLY ENERGIZED AND PREVENT THE BRAKES FROM BEING APPLIED ON ONE OF THE AXLES. AS A RESULT, THE ANTI-WHEEL LOCK WARNING LAMP IS NOT ACTIVATED.
MACK WL 1975

AN AXLE NO BRAKE CONDITION COULD RESULT FROM AN EATON CONTROLLER INTERNAL ELECTRICAL MALFUNCTION. THIS CONDITION MAY CAUSE THE ANTI-WHEEL LOCK VALVE SOLENOID TO BE CONTINUOUSLY ENERGIZED AND PREVENT THE BRAKES FROM BEING APPLIED ON ONE OF THE AXLES. AS A RESULT, THE ANTI-WHEEL LOCK WARNING LAMP IS NOT ACTIVATED.
MACK WL 1976

AN AXLE NO BRAKE CONDITION COULD RESULT FROM AN EATON CONTROLLER INTERNAL ELECTRICAL MALFUNCTION. THIS CONDITION MAY CAUSE THE ANTI-WHEEL LOCK VALVE SOLENOID TO BE CONTINUOUSLY ENERGIZED AND PREVENT THE BRAKES FROM BEING APPLIED ON ONE OF THE AXLES. AS A RESULT, THE ANTI-WHEEL LOCK WARNING LAMP IS NOT ACTIVATED.
MACK WL 1977

A DESIGN DEFICIENCY EXISTS IN THE AIR DRYER PIPING IN THE AREA OF THE PRESSURE RELIEF VALVE AND COMPRESSOR GOVERNOR CONTROL LINK. MOISTURE IS PASSED AND BUILDS UP IN THIS RELIEF VALVE AND CONTROL LINE. IN FREEZING AMBIENT TEMPERATURES, THIS MOISTURE MAY FREEZE, ALLOWING THE CHASSIS AIR SYSTEM PRESSURE TO EXCEED 150 PSI. EXCESSIVE AIR SYSTEM PRESSURE CAN CAUSE SEPARATION OF AIR PIPING CONNECTIONS AND AIR SYSTEM VALVE FAILURE.
MACK WL 1978

A DESIGN DEFICIENCY EXISTS IN THE AIR DRYER PIPING IN THE AREA OF THE PRESSURE RELIEF VALVE AND COMPRESSOR GOVERNOR CONTROL LINK. MOISTURE IS PASSED AND BUILDS UP IN THIS RELIEF VALVE AND CONTROL LINE. IN FREEZING AMBIENT TEMPERATURES, THIS MOISTURE MAY FREEZE, ALLOWING THE CHASSIS AIR SYSTEM PRESSURE TO EXCEED 150 PSI. EXCESSIVE AIR SYSTEM PRESSURE CAN CAUSE SEPARATION OF AIR PIPING CONNECTIONS AND AIR SYSTEM VALVE FAILURE.
MACK WL 1975

A DESIGN DEFICIENCY EXISTS IN THE AIR DRYER PIPING IN THE AREA OF THE PRESSURE RELIEF VALVE AND COMPRESSOR GOVERNOR CONTROL LINK. MOISTURE IS PASSED AND BUILDS UP IN THIS RELIEF VALVE AND CONTROL LINE. IN FREEZING AMBIENT TEMPERATURES, THIS MOISTURE MAY FREEZE, ALLOWING THE CHASSIS AIR SYSTEM PRESSURE TO EXCEED 150 PSI. EXCESSIVE AIR SYSTEM PRESSURE CAN CAUSE SEPARATION OF AIR PIPING CONNECTIONS AND AIR SYSTEM VALVE FAILURE.
MACK WL 1976

A DESIGN DEFICIENCY EXISTS IN THE AIR DRYER PIPING IN THE AREA OF THE PRESSURE RELIEF VALVE AND COMPRESSOR GOVERNOR CONTROL LINK. MOISTURE IS PASSED AND BUILDS UP IN THIS RELIEF VALVE AND CONTROL LINE. IN FREEZING AMBIENT TEMPERATURES, THIS MOISTURE MAY FREEZE, ALLOWING THE CHASSIS AIR SYSTEM PRESSURE TO EXCEED 150 PSI. EXCESSIVE AIR SYSTEM PRESSURE CAN CAUSE SEPARATION OF AIR PIPING CONNECTIONS AND AIR SYSTEM VALVE FAILURE.
MACK WL 1977

A DEFICIENCY EXISTS IN THE WELDS SECURING THE REAR SPRING INSULATOR BRACKET TO THE AXLE HOUSING. THIS IS DUE TO IMPROPER POSITIONING OF THE WELD, IN RELATIONSHIP TO THE BRACKET AND AXLE HOUSING. FAILURE OF THE WELDS WOULD CAUSE SEPARATION OF THE SPRING INSULATOR BRACKET AND THE AXLE HOUSING, RESULTING IN IMPROPER ALIGNMENT OF THE AFFECTED AXLE.
MACK WL 1977

THE FLEX BLADE FANS ON THE INVOLVED VEHICLES MAY DEVELOP CRACKS IN THE LAMINATED STIFFENER AS A RESULT OF FATIGUE DURING OPERATION. IF SUCH A CONDITION EXISTS AND THE CRACKS GO UNDETECTED, CONTINUED OPERATION COULD CAUSE PIECES OF THE STIFFENER TO BREAK OFF.
MACK WL 1973

THE FLEX BLADE FANS ON THE INVOLVED VEHICLES MAY DEVELOP CRACKS IN THE LAMINATED STIFFENER AS A RESULT OF FATIGUE DURING OPERATION. IF SUCH A CONDITION EXISTS AND THE CRACKS GO UNDETECTED, CONTINUED OPERATION COULD CAUSE PIECES OF THE STIFFENER TO BREAK OFF.
MACK WL 1972

THE FLEX BLADE FANS ON THE INVOLVED VEHICLES MAY DEVELOP CRACKS IN THE LAMINATED STIFFENER AS A RESULT OF FATIGUE DURING OPERATION. IF SUCH A CONDITION EXISTS AND THE CRACKS GO UNDETECTED, CONTINUED OPERATION COULD CAUSE PIECES OF THE STIFFENER TO BREAK OFF.
MACK WL 1974

THE FLEX BLADE FANS ON THE INVOLVED VEHICLES MAY DEVELOP CRACKS IN THE LAMINATED STIFFENER AS A RESULT OF FATIGUE DURING OPERATION. IF SUCH A CONDITION EXISTS AND THE CRACKS GO UNDETECTED, CONTINUED OPERATION COULD CAUSE PIECES OF THE STIFFENER TO BREAK OFF.
MACK WL 1975

THE FLEX BLADE FANS ON THE INVOLVED VEHICLES MAY DEVELOP CRACKS IN THE LAMINATED STIFFENER AS A RESULT OF FATIGUE DURING OPERATION. IF SUCH A CONDITION EXISTS AND THE CRACKS GO UNDETECTED, CONTINUED OPERATION COULD CAUSE PIECES OF THE STIFFENER TO BREAK OFF.
MACK WL 1976

THE FLEX BLADE FANS ON THE INVOLVED VEHICLES MAY DEVELOP CRACKS IN THE LAMINATED STIFFENER AS A RESULT OF FATIGUE DURING OPERATION. IF SUCH A CONDITION EXISTS AND THE CRACKS GO UNDETECTED, CONTINUED OPERATION COULD CAUSE PIECES OF THE STIFFENER TO BREAK OFF.